| FWupdate100.zip | Debug serial port DigiPEG firmware update software for Windows version 1.00. |
| FWupdate110.zip |
Debug serial port DigiPEG firmware update software for Windows version 1.10. Fixed some cosmetic bugs. Added the capability to erase the User Data Flash in case an incorrect file prevents DigiPEG from booting. Serial port list is no longer limited to Com4, but it is dynamic built with the serial ports currently installed. |
| FWupdate120.zip |
Debug serial port DigiPEG firmware update software for Windows version 1.20. Added the capability to perform firmware upgrade using the User Serial Port in addition to the Debug/Upgrade port. Note that this is supported for firmware releases 1.17 or greater and also that BootMonitor v3.00 is required. |
| DigiPEG102.Rar | DigiPEG Firmware Release 1.02 Fixed a bug in displaying serial number, which was displaying an internal counter (normally a very low number) instead of the real serial number. Fixed a bug in SetEncoder command. Fixed a nasty bug in command line parsing that could lead to hangups and rejection of valid commands. Added display on OSD (AUX7 button, while in DevBoard mode) informations about the current decoding channel. Fixed an incorrect OSD clear in Fast Setup menu. Added Channel command. |
| DigiPEG103.Rar | DigiPEG Firmware Release 1.03 Added digital audio input support. Added SetDigitalAudioIn, SelAudioIn, SetEncoderSR, ColorBars commands. |
| DigiPEG104.Rar | DigiPEG Firmware Release 1.04 Forced a full channel resync if too many audio only syncs are done. Fixed incorrect Audio input LED indication on DevBoard if there was no DigitalAudioIn enabled. Added digital audio output support. Added SetDigitalAudioOut command. |
| DigiPEG105.Rar | DigiPEG Firmware Release 1.05 Cleaned up SAA7113 and SAA7129 settings with a Tektronix VM700. Upgraded FPGA to revision 1.06. Implemented commands for the built in TS multiplexer. Implemented user data flash with the capability to upload custom video/audio splash files. Implemented audio output volume control. |
| DigiPEG106.Rar | DigiPEG Firmware Release 1.06 Fixed a bug that caused the 'locked' indication disapper even if the system was working correctly. Fixed a bug in the UserDataDelete command. Implemented the I2CPatch file. Implemented the EncoderParms file. Implemented the FPGA file. Added the capability to select what to decode at boot. Added clock frequency selection when clock master. |
| DigiPEG107.Rar | DigiPEG Firmware Release 1.07 Upgraded FPGA to revision 1.07. Added experimental harddisk/playback user serial commands. Added Rs232 service channel option. Added the option to disable the MPEG2 encoder to reduce power consumption. Added transport stream watchdogs. Added help command. |
| DigiPEG108.Rar | DigiPEG Firmware Release 1.08 Non public release. |
| DigiPEG109.Rar | DigiPEG Firmware Release 1.09 Upgraded FPGA to revision 2.03. Improved media monitoring robustness in particular when there are lot of errors in the transport stream. Defined 16 user available eeprom bytes. Fixed a bug in the service channel option that prevented the possibility to enable the Tx or the Rx separately. Added specific firmware for the Fujitsu MB86391 encoder. Added lots of GetXXXX commands. |
| DigiPEG110.Rar | DigiPEG Firmware Release 1.10 Added LoadTables, UserDataType, UserAsciiUpload, GetVideoPresence, SelInputStandard, SetOutputStandard, LoadMessages. Added documentation on DVBTables user file for PAT/PMT/NIT/SDT insertion in the transport stream. Added partial support for non PAL systems. |
| DigiPEG111.Rar | DigiPEG Firmware Release 1.11 Upgraded FPGA to revision 2.05 Added DigitalVideoIn, Delay Added batch and ram files support Added ASI support Fixed a bug that could cause TSWatchDog to fail |
| DigiPEG112.Rar | DigiPEG Firmware Release 1.12 Fixed vertical screen aligmnent Fixed an incorrect answer to the DigitalVideoIn command Added TestVideoLines |
| DigiPEG113.Rar | DigiPEG Firmware Release 1.13 Several minor bugs fixed No new options (documentation is the same as version 1.12) |
| DigiPEG114.Rar | DigiPEG Firmware Release 1.14 Upgraded FPGA to revision 2.06 Fixed bug on ASI output Added PCR Restamper Added support for private streams in the PMT Added an example of the DVBTables file in the distribution archive |
| DigiPEG115.Rar | DigiPEG Firmware Release 1.15 Upgraded FPGA to revision 2.07 Changed configuration setups from 4 to 2 Added TeleText extraction from Analog Signal and multiplexing in the TS Added a simple command to set the PIDs for the Encoder Some minor bugs fixed Changed "MUX" license: The internal TS multiplexer is now generally available for multiplexing "reduced" DVBTables or to overcome the 16MBit TS limitation. Multiplexing two TSs still requires the "MUX" license. |
| DigiPEG116.Rar | DigiPEG Firmware Release 1.16 Upgraded FPGA to revision 2.10 Added EncEncode, ADV7194Config, ADV7194SetVideoOut, ScopusPatch, OSDEnable, OSDParams, OSDText Extended the SetTSWatchdog command Extended the SetEncoder and GetEncoder commands Extended the SetMux command Fixed TeleText on analog output Fixed a bug that could rarely cause media monitoring to fail |
| DigiPEG117.Rar | DigiPEG Firmware Release 1.17 Upgraded FPGA to revision 2.11 Fixed a bug on ShowMPEGInfo/GetMPEGInfo commands when not decoding video Fixed a bug that could cause user serial lockup in case of bad commands Added Clock/Calendar support and ClockGet, ClockSet commands Added TransportStreamStatus, Encoder Halt Added I2CPATCH.D50, .E50, .D60 and .E60 files and extended the DoI2CPatch command Added InsertUserPacket and PACKETx files Added multiple No Transport Stream lines in MESSAGES file Added TimeTables file and LoadTimeTables for TDT and TOT insertion in the TS Added NetworkOther, DeliverySystemOther and ChannelOther in the DVBTables file |
| BootMonitorV3.rar | DigiPEG Boot Monitor Version 3 Boot Monitor Version 3, needed for Firmware upgrade using the User Serial Port |
| DigiPEG118.Rar | DigiPEG Firmware Release 1.18 Fixed a bug that could cause problems when selecting Parallel TS In when ASI Out is configured too. Added AUTOEXEC file. Added TTXFixup, GetDecoderStatus, ChResyncMode, HideFWVersion, LowDelayTx, LowDelayRx, LowLatencyRx, EITEvent, EITClearEvent, EITClearAll, Config1WriteProtect, OptimizeAudioPES, MuxIn0PIDFilter, ConfigBackup, ConfigRestore. Added modem remote management and LoadModemFile. Added Mpeg System Bitrate menu user list with the MPEGSYSTEMBR file. Added COFDM Modulator DigiPEG extensions. Added QPSK Modulator DigiPEG extensions. |
| indietro | inizio pagina |